Charging station brackets (pair)
A pair of wall brackets for a 10-port USB charging station, one on each end. The clips follow its angled corners, so it snaps in and stays put.
- Plastic
- 52 g
- Print time
- 5 h 26 min
$14 eachOrder
Broken part? Missing bracket? I'll design one that fits.
Send a photo and a few measurements. I draw the part to your numbers, print it in tough PLA+ here in Sebastian, and you pick it up or get it shipped a few days later.
How it works
You don't need a 3D file or any design skills. A phone photo is enough to start.
Send a photo and measurements
A photo with a ruler or tape measure in it is perfect. Tell me what the part attaches to and what it has to hold.
See it before it prints
You get a 3D preview and the exact price before I print anything. Most designs are ready the same day.
I print it
PLA+ for most parts. PETG for parts that sit in the sun or near heat, like on a boat or in a car.
Pick it up or get it shipped
Free pickup in Sebastian, or tracked USPS shipping anywhere in the US. You pay the postage, shown with your quote.
Parts I've made
Each one was designed to fit one specific job, then printed on the shop's own printer. Plastic and print times are the real ones.
Phone stand
Holds a phone in its case at an easy reading angle. A notch in the front lip lets the charging cable through.
- Plastic
- 62 g
- Print time
- 6 h 3 min
$14 eachOrder
Stove knob
A replacement for a lost or cracked stove knob. Fits the common D-shaped shaft, with ridges round the side for grip and a pointer line on the face.
- Plastic
- 12 g
- Print time
- 1 h 22 min
$9 eachOrder
Broom and tool rack
Three snap-in rings sized to the handles, on a plate with two countersunk screws. Brooms click in and stay off the floor.
- Plastic
- 32 g
- Print time
- 3 h 34 min
$12 eachOrder
Screw tray
Three compartments for loose hardware on the bench. Thin walls, printed in one piece.
- Plastic
- 36 g
- Print time
- 3 h 54 min
$12 eachOrder
Over-door towel hook
Sized to the door it hangs on, so it sits snug without rattling or scratching the paint.
- Plastic
- 17 g
- Print time
- 1 h 48 min
$9 eachOrder
Prices
You see the exact price with the preview. These are typical ranges.
| Part | Typical print time | Price |
|---|---|---|
| Clip, knob, spacer or cap | Under 1 hour | from $8 |
| Bracket or wall mount | 2 to 3 hours | $8 to $15 |
| Stand, holder or organizer | 4 to 6 hours | $10 to $20 |
| Larger or multi-part builds | 8 hours or more | quoted |
Design fee
$15
For a simple custom part, like a bracket, hook, knob or clip. Bigger designs get a fixed price up front, so there are no surprises.
You pay the design fee once. Extra copies, now or later, are just the print price.
Shipping
Pickup in Sebastian is free. Shipped orders go USPS with tracking, and you pay the postage. It's set by the packed weight and shown with your quote, so the total is known before anything prints.
| Packed weight | Typical order | Shipping |
|---|---|---|
| Up to 6 oz | A knob, clip or spacer | $7.00 |
| Up to 12 oz | A bracket or hook | $8.50 |
| Up to 1 lb | A stand or tray | $10.00 |
| Up to 2 lb | A few parts together | $12.50 |
| Up to 3 lb | A bigger order | $15.00 |
| Up to 5 lb | A large build | $18.50 |
| Over 5 lb | Heavy orders | quoted |
What I don't make
Saying no to these keeps everyone safe and legal.
- Parts for certified aircraftThe FAA requires approved parts. Flight-sim panels, kneeboard parts and hangar organizers are fine.
- Weapons or weapon partsOf any kind, including accessories.
- Copies of brands and charactersNo trademarked logos or movie characters. Original designs only.
- Anything that holds a personPlastic prints aren't rated for climbing, seating or safety gear.
Send your part
Tell me what you need and attach a photo or file. I'll reply by email with a preview and a price, usually within a day.
Made on the Treasure Coast.